Category Archives: cb radio
I see the lovely people at Nevada Radio were again selling the Alinco DR-135UK 10m radio for the bargain price of £99 the other day.
I bought one last year from them for the same price as part of the Black Friday event and its been fitted in my car ever since.
Apart from the cheap microphone that needs a squirt of switch cleaner every now and again its been a great radio for the money.
One of the great things about these radios is they are pc programmable.
I have mine set up with the UK FM on band A and bands B through to F are the Super Low to Super High 26.065 to 28.305.
As you can have up to 60 channels per band i have some of the 10m band and repeater channels from 40 to 60 on F band.
Along with that i have set the roger bleep tone and length to mimic the Ham International type bleep.
If you want to down load the software and a copy of the data file i wrote for my radio you can find a zip file HERE
A mate of mine has been nagging me for weeks to make him a roger bleep.
Not just any bleep but the uber annoying peewit that is found in the Hy-Gain V radios.
He could of bought one from ebay but I have fitted them in the past and they never really sounded right even after messing with the components. This one got the thumbs up from the critics on channel 14 in Leicester.
I really should get some etching stuff and knock some pcbs up but time is always the issue. Mind you when the lids on you cant see the stripboard anyway…
Ham International Concorde 2 in to sort out. Service and remove dodgy extra blocks. Fm audio was quiet and lacked any presence. After a bit of looking I discovered D4 the fm mod varicap was missing and had never been fitted at the factory! Sounds much better now. Must have been a Friday afternoon radio
The ever popular Ham International jumbo and its mobile counterparts the Multimode 2,Concorde 1 and Major 588 and not a bad radio for their age but they do have some niggling faults.
One of these is the awful FM modulation. Most modern radios apply the fm tx audio to the vco using a varicap diode.
In these earlier radios cybernet modulated the crystals to get the deviation. This results in poor and quiet audio which when turned up makes the radio wander about on transmit frequency.
The squelch is also renowned for popping as it opens and closes. My good friend Paul Michelin Man in Leicester worked out a mod which cures this and details are at the bottom of the page.
The other is a lack of the correct bias voltage on the output transistor. This can be fixed by changing R38 to a 15 ohm resistor.
You will then need to measure the bias voltage on the base of Q10.Key the radio up on SSB with no modulation to measure this. It needs to be 0.7 volts and can be adjusted with RV1.
The way i do them is.. Remove L3 and C30. Link out R26 Connect a 10000pf (103) cap to Pin 2 of IC2. To the other end of the cap connect a 10k resistor and the cathode (with the line on) of an ITT310 or 410 Varicap diode. The other end of the varicap and resistor goes to ground.
Then solder a 220k resistor to the cathode of the varicap and connect the other end of this resistor to the point on the board where you removed L3 and C30 from (R25)
Replace C32 with a 100000pf (104) capacitor.
You will just have to adjust the deviation using RV3 and check that the vco locks on all the bands. I have tried using other varicaps but these ones sound the best.
Squelch Pop Mod
Jumbo Owners Manual
There is always a lot of discussion about which is best cybernet or uniden ssb radios. Personally I like cybernet stuff but I admit uniden ssb export radios do work well on ssb.
A lot of the issues people have with cybernet stuff is a result of the way that they left the factory. Common complaints are scratchy ssb audio and awful fm transmit audio.
Below are a few things you can do to the 121 chassis. This is used in radios like the Hy-gain 2795,Tristar 747, Concorde 2 and lots of others including some Colt Excaliburs and the rare Major 688.
These simple mods will cure the ssb and fm audio
To improve the audio limiter performance change R150 to a 5.6k ohm
Also change R166 to a 5.6k ohm.
Also add a 1000pf (102) Capacitor One side to the junction of R28 and C32 and the other to ground.
Check the FM deviation level and adjust if needed using RV1
Change R40 to a 33 ohm to improve the bias on the driver transistor.
Change R44 to a 15 ohm and set the bias to the output transistor using RV2 by keying up the radio up on ssb with no audio and set the voltage on the base of Q10 to 0.7 volts.
To stop the popping squelch remove R132 and add a link wire as shown below